ºìÌÒÊÓƵ

Phase / Frequency Detectors | MC100EP40

Phase-Frequency Detector, 3.3 V / 5 V, ECL Differential

Active

Datasheet

ºìÌÒÊÓƵ

Overview

The MC100EP40 is a three-state phase-frequency detector intended for phase-locked loop applications which require a minimum amount of phase and frequency difference at lock. Advanced design significantly reduces the dead zone of the detector. For proper operation, the input edge rate of the R and V inputs should be less than 5 ns. The device is designed to work with a 3.3 V / 5 V power supply.

When Reference (R) and Feedback (FB) inputs are unequal in frequency and/or phase the differential UP (U) and DOWN (D) outputs will provide pulse streams which when subtracted and integrated provide an error voltage for control of a VCO.

When Reference (R) and Feedback (FB) inputs are 80 pS or less in phase difference, the Phase Lock Detect pin will indicate lock by a high state. The VTX (VTR, VTRbar , VTFB , VTFBbar ) pins offer an internal termination network for 50 line impedance environment shown in Figure 2. An external sinking supply of VCC-2 V is required on VTX pin(s). If you short the two differential VTR and VTR (or VTFB and VTFBbar ) together, you provide a 100 termination resistance that is compatible with LVDS signal receiver termination. For more information on termination of logic devices, see AND8020.

The VBB pin, an internally generated voltage supply, is available to this device only. For single-ended input conditions, the unused differential input is connected to VBB as a switching reference voltage. VBB may also rebias AC coupled inputs. When used, decouple VBB and VCC via a 0.01 F capacitor and limit current sourcing or sinkingto 0.5 mA. When not used, VBB should be left open.

For more information on Phase Lock Loop operation, refer to AND8040.

Special considerations are required for differential inputs under No Signal conditio

  • Maximum Frequency > 2 Ghz Typical
  • Fully Differential
  • Advanced High Band Output Swing of 400 mV
  • Theoretical Gain = 1.11
  • Trise 97 pS Typical, Ffall 70 pS Typical
  • The 100 Series Contains Temperature Compensation
  • PECL Mode Operating Range: VCC = 3.0 V to 5.5 V with VEE = 0 V
  • NECL Mode Operating Range: VCC = 0 V with VEE = -3.0 V to -5.5 V
  • 50Ω Internal Termination Resistor
  • These are Pb-Free Devices

Product Resources

Product services, tools and other useful resources related to MC100EP40

CAD Model

CAD Model

Material Composition

Product Change Notification

Reliability Data

Product List

If you wish to buy products or product samples, please log in to your ºìÌÒÊÓƵ account.

Search

Close Search

ºìÌÒÊÓƵ:

2

Share

Sort by

Product Groups:

┗

Orderable Parts:

2

Product

Status

CAD Models

Compliance

Package Type

Case Outline

MSL Type

MSL Temp (°C)

Container Type

Container Qty.

ON Target

Input Level

Output Level

VCC Typ (V)

Transfer Gain Typ (mV/degree)

CMRR Max (V)

fToggle Max (MHz)

tpd Typ (ns)

tJitter Typ (ps)

tR & tF Max (ps)

Reference Price

MC100EP40DTG

Loading...

Active

CAD Model

Pb

A

H

P

TSSOP-20

9.48

1

260

TUBE

75

Y

ECL

ECL

5

0.93

2

2000

0.55

0.2

150

Price N/A

More Details

MC100EP40DTR2G

Loading...

Active

CAD Model

Pb

A

H

P

TSSOP-20

9.48

1

260

REEL

2500

Y

ECL

ECL

5

0.93

2

2000

0.55

0.2

150

Price N/A

More Details

Show More

1-25 of 25

ºìÌÒÊÓƵ per page

Jump to :

1

Product Support

If you're interested to learn about this ºìÌÒÊÓƵ product, contact sales by filling out the form below.

Reliability Data

Die Related Summary Data

Device: MC100EP40DTG

Equivalent to wafer fab process: MOSAIC

Product Technology

Product Technology

Equivalent Device-Hours

MTBF/MTTF in Hours

FITS

MOSAIC

0

476668904

More Details

Re-calculate Data

Data is based on the following assumptions.

Note: The temperature and confidence level may be adjusted to your requirements.

Disclaimer: A reliability FIT rate calculated using this tool shall not be used for any functional safety purpose. In case a raw FIT rate needs to be estimated for a component which is targeted to be used in a safety critical application (i.e. compliant to ISO 26262 standard) it should be calculated according to generic safety standards (IEC62380, IEC61709, SN29500, FIDES, etc.)

New Search
Email Sales
Please provide a first name.
Please provide a last name.
Please provide a company/university name.
Please provide a valid email.
Please choose a country.
Please choose a job title.
Please provide a how could we help you.
You have to agree with the privacy policy.

This site is protected by reCAPTCHA and the Google and apply.

Hello, your current browser settings are preventing us from processing your submission. You can adjust your browser settings and reload the page or you can submit an email directly to inside.sales@ºìÌÒÊÓƵ.com

You might also try the following:

  • Clear your browser cookies
  • Try to open this page in anonymous browser window
  • Try a different browser
  • Make sure you have reliable internet connection

Thank you for submitting the contact sales form. Your request is on its way to our sales support team!

We thank you for your interest in ºìÌÒÊÓƵ and are working on your request. Our sales support team will respond to your request within two business days.